Free STL file Geeetech A10M Marlin 1.1.9 Firmware đ§ââïžă»3D printer design to downloadă»Cults
Por um escritor misterioso
Last updated 19 janeiro 2025
This is Marlin 1.1.9 Firmware for Geeetech A10M printers with mixing extruder. I ported all Geeetech features from Geeetech
This is Marlin 1.1.9 Firmware for Geeetech A10M printers with mixing extruder. I ported all Geeetech features from Geeetech's 1.1.8 version, which include: - Full BLTouch support with my hack allowing to fine tune small build plate tilts which could not be eliminated by autolevel alone; BLTouch is enabled by default, disable it by commenting #define BLTOUCH line in the Configuration.h file if needed. - Power loss recovery/resume. I tried to activate a native Marlin power loss feature but it turned out that it won't compile due to global variable's memory exhaustion. Finally I decided to port a limited Geeetech's version of this feature which appeared working pretty good. - Gradient mix/Filament mixer features. Current Marlin version has just a rudimentary support for mixing extruders, there still a lot of bugs and sub-optimal code implementations in this extent. I made some chacnges in the original Marlin code to make a mixing extruder work fine. As such I made a number of bug fixes for Filament Change feature, including the implementation of M701/M702 g-codes. - Fine-tuned extrusion parameters, as such I calibrated the extruders increasing Steps per mm value from 340 to 430. - Runout sensors enabled; - Other tweaks and tune ups. A couple of words about tilting compensation hack. My experience of working with different machines using auto-level feature under Marlin firmware shows that all hardware has a consistent auto-level error causing a tilt of the build plate to one of the corners which can reach tenths of mm in some cases. Every hardware I used had this tilt error of unclear nature which may differ in a particular corner to tilt to, but it doesn't depend on a sensor type (I used inductive, capacitive and, of course, BLTouch - all of them had that tilt error). So after a lot of unsuccessful attempts to tweak this using Marlin features alone, I made my own hack in the Marlin code to resolve this issue. I added a few lines to the Configuration.h file to control this feature: \#define TILT_COMPENSATION \#if ENABLED(TILT_COMPENSATION) \#define X_TILT_COMP 0.04 // lower value - left bed edge higher \#define Y_TILT_COMP 0.3 // lower value - front bed edge higher \#endif These are values that work for my machine, which may or may not fit your one. In the case you see a distinctive tilt into one or both sides of the build plate, first try to disable this feature and perform a test print. Tweak X_TILT_COMP and Y_TILT_COMP if needed to achieve an absolutely flat first layer printout. Use leveling_test.stl model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this firmware: ;Start G-Code G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 ;move X/Y/Z to min endstops (Homing) G29 ;start auto level G1 Z15.0 F9000 ;move the platform down 15mm G92 E0 ;zero the extruded length G0 F7200.000000 X1.0 Y160 Z0.300 ;move the caret to the left edge of the bed G1 F1800.000 X1.0 Y110.0 E10 ;purge filament G1 X0 Y110 E13 ;purge more filament G1 X0 Y60 E16.0 ;purge even more G92 E0 ;zero the extruded length again G1 F1500 E-6.5 ;retract G1 Z30.0 Y-5.0 ;rise the caret T0 ;switch to extruder 0 M420 S1 ;resume Auto-leveling after extruder change M117 Printing ;----------------------------------------------------------- ;End G-Code: M104 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;----------------------------------------------------------- ;Switch Extruder 1 G-Code M420 S1 ;resume Auto-leveling after extruder change ;----------------------------------------------------------- ;Switch Extruder 2 G-Code M420 S1 ;resume Auto-leveling after extruder change ;----------------------------------------------------------- Update 2: Important Found a bug in the e-factor for the extruders feed rate, causing the second extruter to perform incorrectly in some circumstances (thanks to the user szerwi). Firmware file updated, please download the latest version and re-flash.
This is Marlin 1.1.9 Firmware for Geeetech A10M printers with mixing extruder. I ported all Geeetech features from Geeetech's 1.1.8 version, which include: - Full BLTouch support with my hack allowing to fine tune small build plate tilts which could not be eliminated by autolevel alone; BLTouch is enabled by default, disable it by commenting #define BLTOUCH line in the Configuration.h file if needed. - Power loss recovery/resume. I tried to activate a native Marlin power loss feature but it turned out that it won't compile due to global variable's memory exhaustion. Finally I decided to port a limited Geeetech's version of this feature which appeared working pretty good. - Gradient mix/Filament mixer features. Current Marlin version has just a rudimentary support for mixing extruders, there still a lot of bugs and sub-optimal code implementations in this extent. I made some chacnges in the original Marlin code to make a mixing extruder work fine. As such I made a number of bug fixes for Filament Change feature, including the implementation of M701/M702 g-codes. - Fine-tuned extrusion parameters, as such I calibrated the extruders increasing Steps per mm value from 340 to 430. - Runout sensors enabled; - Other tweaks and tune ups. A couple of words about tilting compensation hack. My experience of working with different machines using auto-level feature under Marlin firmware shows that all hardware has a consistent auto-level error causing a tilt of the build plate to one of the corners which can reach tenths of mm in some cases. Every hardware I used had this tilt error of unclear nature which may differ in a particular corner to tilt to, but it doesn't depend on a sensor type (I used inductive, capacitive and, of course, BLTouch - all of them had that tilt error). So after a lot of unsuccessful attempts to tweak this using Marlin features alone, I made my own hack in the Marlin code to resolve this issue. I added a few lines to the Configuration.h file to control this feature: \#define TILT_COMPENSATION \#if ENABLED(TILT_COMPENSATION) \#define X_TILT_COMP 0.04 // lower value - left bed edge higher \#define Y_TILT_COMP 0.3 // lower value - front bed edge higher \#endif These are values that work for my machine, which may or may not fit your one. In the case you see a distinctive tilt into one or both sides of the build plate, first try to disable this feature and perform a test print. Tweak X_TILT_COMP and Y_TILT_COMP if needed to achieve an absolutely flat first layer printout. Use leveling_test.stl model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this firmware: ;Start G-Code G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 ;move X/Y/Z to min endstops (Homing) G29 ;start auto level G1 Z15.0 F9000 ;move the platform down 15mm G92 E0 ;zero the extruded length G0 F7200.000000 X1.0 Y160 Z0.300 ;move the caret to the left edge of the bed G1 F1800.000 X1.0 Y110.0 E10 ;purge filament G1 X0 Y110 E13 ;purge more filament G1 X0 Y60 E16.0 ;purge even more G92 E0 ;zero the extruded length again G1 F1500 E-6.5 ;retract G1 Z30.0 Y-5.0 ;rise the caret T0 ;switch to extruder 0 M420 S1 ;resume Auto-leveling after extruder change M117 Printing ;----------------------------------------------------------- ;End G-Code: M104 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;----------------------------------------------------------- ;Switch Extruder 1 G-Code M420 S1 ;resume Auto-leveling after extruder change ;----------------------------------------------------------- ;Switch Extruder 2 G-Code M420 S1 ;resume Auto-leveling after extruder change ;----------------------------------------------------------- Update 2: Important Found a bug in the e-factor for the extruders feed rate, causing the second extruter to perform incorrectly in some circumstances (thanks to the user szerwi). Firmware file updated, please download the latest version and re-flash.
Free STL file Geeetech A10M - getting started - A10M landing pageă»3D printing idea to downloadă»Cults
Geeetech best 3D printer modelsă»410 designs to downloadă»Cults
Geeetech best 3D printer modelsă»410 designs to downloadă»Cults
A10m best STL files for 3D printingă»78 models to downloadă»Cults
Geeetech best 3D printer modelsă»410 designs to downloadă»Cults
Free STL file Geeetech A10M - getting started - A10M landing pageă»3D printing idea to downloadă»Cults
A10m best STL files for 3D printingă»78 models to downloadă»Cults
Free STL file Geeetech A10M Marlin 1.1.9 Firmware đ§ââïžă»3D printer design to downloadă»Cults
Geeetech best 3D printer modelsă»410 designs to downloadă»Cults
Recomendado para vocĂȘ
-
ExtruderSpeed() function for 3D printing with ABB IRB12019 janeiro 2025
-
Any idea why my printer, after bed levelling, will raise up, then just spin around? (details in comments) : r/3Dprinting19 janeiro 2025
-
Resume after print fail, help please D: : r/3Dprinting19 janeiro 2025
-
Shows the parts of G code a First Part b Second Part c Third Part19 janeiro 2025
-
Ultimaker 3 Tricks & Tips â Dan K Chen19 janeiro 2025
-
gcode brings printer out of range · Issue #7453 · prusa3d/PrusaSlicer · GitHub19 janeiro 2025
-
Printer has gone crazy!19 janeiro 2025
-
Development of graphics user interface (GUI) for process planning in extrusion based additive manufacturing - ScienceDirect19 janeiro 2025
-
Communication error at the start of a new 3D-print - Get Help - OctoPrint Community Forum19 janeiro 2025
-
Anet a8 ĐœĐ” пДŃĐ°ŃĐ°Đ”Ń ĐžĐ· Cura19 janeiro 2025
vocĂȘ pode gostar
-
katsute kami datta kemono-tachi e todos os episĂłdios19 janeiro 2025
-
Grand Theft Auto III PC NEW Sealed UK Version Grand theft Auto 3 GTA III19 janeiro 2025
-
What is your best tactic for making semi-realistic or realistic windows? - Building Support - Developer Forum19 janeiro 2025
-
i just noclipped into the backrooms : r/bindingofisaac19 janeiro 2025
-
Tanjiro Demon Slayer Zenitsu is a Fearsome Demon Slayer Who Wields a Deadly and Terrifying Weapon · Creative Fabrica19 janeiro 2025
-
AmiAmi [Character & Hobby Shop] Big Leather Strap Yama no Susume Omoide Present 03 / Kaede (SD Christmas ver.)(Released)19 janeiro 2025
-
Rei Car Multimarcas19 janeiro 2025
-
Gereja Katolik SANTO MIKAEL: DOA-DOA DASAR IMAN KATOLIK19 janeiro 2025
-
FNF One Last Funk â Sonic.EXE One Last Round Mod - Play Online19 janeiro 2025
-
Desenhos para colorir de dragon-ball-z para imprimir - Dragon Ball Z - Just Color Crianças : Påginas para colorir para crianças19 janeiro 2025